There are currently no product reviews.
This is an excellent handbook. We had no information on the appliance until we obtained this and are now able to use the appliance to its full potential. Strongly recommended.
Very happy to find this from owners-manual.com and the enclosed spec sheet as well.
Not longer available from Sony.
The Owner's manual was very helpful. The WEGA is about 35 years old and needed repair.
Your Website is pretty good und easily to handle.
Perfect. Very good service and very good scanning quality. All sheets are very legible. Thank's
My first manual from Owner-Manuals.com but not the last! I am very satisfied with the easy ordering and promt delivery of a manual I did not find anywhere else.
Programming with âVIDEOPlus+â
All the information required for a programming is encoded in the VIDEOPlus+ code.
1 Switch on the TV set. 2 Press the TIMER k button on the remote control. 3 With the digit buttons 0-9 , enter the VIDEOPlus+ code (up to 9 digits) printed in your TV guide next to the
How to programme a recording manually
1 Switch on the TV set. Press the TIMER k button twice. 2 Select a free TIMER block, using the P q or the P r button. Press the TIMER k button.
DATE PROG START V/P END 01 01 20:00 21:30
start time of a TV programme. If you make a mistake, clear with the CLEAR (CL) button.
4 If you want to programme at daily or weekly intervals, press the
vals) or âW-WEEKLYâ (weekly intervals) appears in the display. The âdaily intervalsâ function can only be used for recordings to be made from Mondays to Fridays inclusive.
SELECT button until âD-DAILYâ (daily inter-
-----------------------NEXT gTIMER CLEAR gCL -/+ 0-9 D/WgSELECT OK 3 With the TIMER k button you select between the entries âDATEâ (date), âPROGâ (programme number),
5 Confirm the entries with the OK button . The resultant data appears on the TV screen.
Note: If you use VIDEOPlus+ for the first time for this TV channel, the line âSELECT PROGâ appears when you confirm the VIDEOPlus+ code. Instead of âE2â, select the programme number for this particular TV channel, using the digit buttons 0-9 and confirm with the OK button. * Switch âVPSâ or âPDCâ (V/P) on or off with the SELECT button. * If you wish to set a later end time for a recording, press the P q button at step 5 . Each time you press the P q button you will add 15 minutes to the end time. * If e.g.: â20:00â flashes in the display, please set the clock.
6 Finally, press the OK button. Programming is now complete. 4
âSTARTâ (start time) and âENDâ (stop time). You can enter or adjust data, using the P q or the P r button or the digit buttons 0-9 . Confirm each entry with the TIMER k button. You can switch âVPS/PDCâ (âV/Pâ) on and off at step âSTARTâ with the SELECT button. You can select between âDâ (daily intervals) or âWâ (weekly intervals) at step âDATEâ with the SELECT button. Finally, press the OK button. Programming is now complete.
5 Make sure that a cassette without erase protection has been loaded. Switch to standby with the STANDBY m button. A programmed recording will only function when the video recorder is switched to standby with the STANDBY m button.
The data has been stored in a TIMER block.
7 Make sure that a cassette without erase protection has been loaded. Switch to standby with the STANDBY m button.
A programmed recording will only function when the video recorder is switched to standby with the STANDBY m button.
Note: * Clear a TIMER-block: After step 1 , select the TIMER block you want to clear with the P q or the P r button. Press the CLEAR (CL) button. * If e.g.: â20:00â flashes in the display, the clock must be set.