There are currently no product reviews.
A comprehensive Operating and Service Manual. All schematics are complete and easy to read. The PCB drawings and complete parts list are very helpful. I would definitely recommend this manual.
SCANNING OF HIGH QUALITY
VERY, VERY HIGH VELOCITY DOWNLOAD
VERY GOOD PRICE,
TRUE SATISFIED, THANKS
Genuine Toshiba owner's manual. Couldn't really ask for more. And written in understandable English in contrast to a few recent experiences I have had with manuals for other equipment other than Toshiba but made in China and written in "Chinglish"!
I purchased a vintage Sony mixer off eBay and within the hour was able to locate and purchase the manual for it.I mean really,where else can you find a manual for a product made in 1983!? It was easy to find and purchase/download the manual I needed.I will use this site again for other equipment I have! Great site!
manual de usuario perfecto y completo de buena calidad de impresion y muy detallado ideal !
Save These Instructions Caution:
To reduce the risk of fire or injury to persons, read and follow these instructions.
1 Chose a spot near an electric outlet and a telephone jack outlet. 2 Install the handset antenna Slide the metal tip of the handset antenna straight down into the opening in the top of the handset. Turn the antenna clockwise to make sure the tip is set in place, and continue until it is sung against the top of the handset. Do not over tighten. 3 Install the handset battery â¢ Remove the battery compartment cover on the handset by pressing on the identation and sliding the cover downward â¢ Plug the battery pack cord into the handset, and tuck the cords in next to the battery â¢ Replace the cover by sliding it on its track 4 Set Tone or Pusle dialing â¢ Press Memory button â¢ Press Recall button â¢ Press for Tone, or for Pulse â¢ French version do not have this function 5 Connect the telephone line cord â¢ Plug one end of the telephone line cord into the jack on the top of the base â¢ Plug the other end into a modular telephone jack 6 Mount the base on the wall (wall installation only) â¢ Mark and drill two holes in a wall stud, 3 5/16" apart â¢ Use two wall screws, leaving about 1/4" free of the wall â¢ Plug one end of the telephone line cord into the jack on the top side of the base â¢ Plug the other end into a modular telephone jack â¢ Mount the base unit on the wall by aligning the two holes on the back with screws â¢ Slide the base unit down in place 7 Plug the power cord â¢ Plug the one end of the power cord into the jack on the top side of the base â¢ Plug the AC adapter on the power cord into an electric outlet 8 Charge the handset battery pack for at least 12 hours Place the handset in the base, the CHARGE light on the base goes on to show the handset is in the right position to charge the battery pack. 9 Check for dial tone After the battery pack is charged, pick up the handset and extend the base antenna. Check for dial tone by pressing the , the IN USE light on the base should go on, and you should hear a dial tone. 10 Set TBR time The flash time is pre-set for end users, users do not switch it under normal usage. The TBR times switch is located on the top side of the base. Three flash time, A-100ms, B-270ms and C620ms are available for different telephone network system. Select suitable flash time if necessary.
! CAUTION: Use only the AC power adapter supplied with this telephone. Power supply 92201160DV Input : 230V AC 50Hz 45mA Output : 9Vâ¦220mA 1.98VA 11Vâ¦60mA 0.66VA
The handset and base can communicate over only a certain distance - which can vary with the locations of the base and handset, the weather, and the construction of your home or office. For best performance, make sure the base antenna is fully upright. If the handset is moved to a point where the base and handset can longer communicate, you are âout of rangeâ. When you try to make a call, the handset will beep to indicate that you are out of range. If you receive a call while you are out of range, the handset might not ring - or if it does ring, the call might not connect when you press . Move closer to the base, then press to answer the call. If you move out of range during a phone conversation, you may be disconnected. Changing Channels This cordless telephone has multi channels available for maximum performance. If you notice noise or interference while using the handset: 1. Press . 2. If the interference doesnât clear, continue to press until you find a clear channel. - OR Move closer to the base and press .
NOTE: You must be in range to change channels.
USER MANUAL / MODE DâEMPLOI
Multi channel cordless phone / TÃ©lÃ©phone sans fils multi-canal
1. Use only the battery(ies) instructed. 2. Do not dispose of the battery(ies) in a fire. The cell may explode. Check with local codes for possible special disposal instructions. 3. Do not open or multilate the battery(ies). Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed. 4. Exercise care in handling batteries in order not to short the battery with conducting materials such as rings, bracelets, and keys. The battery or conductor may overheat and cause burns. 5. Charge the battery(ies) provided with or identified for use with this product only in accordance with the instructions and limitations specified in this manual.
1. Never install telephone wiring during a lightning storm. 2. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. 3. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. 4. Use caution when installing or modifying telephone lines.
Memory This cordless phone can store 10 telephone numbers that you can dial by pressing and one of the number buttons. Additionally, you can store a memory number in the memory location. Storing Memory Numbers 1. Make sure the handset is off. 2. Press . 3. Enter the phone number (up to 20 digits). 4. Press . 5. Press any number button from 0 to 9 for the memory location where the number is to be stored. - OR - Press to store the number in memory location M1.
For example, to store 555-1234 in memory location 3, . NOTE: You may choose to store emergency numbers in memory locations.This feature is provided only as a convenience and the manufacturer assumes no responsibility for reliance upon the memory feature.
Storing a Pause in a Memory Number 1. When storing a number in memory (see above), press 2. Press once inserts a two-second pause.
where you want the dialing pause to occur.
For example, to store 9, Pause, 555-1235 in memory location 3, press
Dialing Memory Numbers 1. Press . 2. Press and the number button of the memory location. - OR - Press
! CAUTION: To reduce the risk of fire or injury to persons or damage to the telephone, read and follow these instructions carefully. â¢ Use only provided Replacement Battery. â¢ Do not dispose of the battery in a fire.The cell might explode. Check with local codes for special disposal instructions. â¢ Do not open or mutilate the battery. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed. â¢ Exercise care in handling batteries in order not to short the battery pack with conducting materials such as rings, bracolets, and keys. The battery pack or conductor may overheat and cause harm. â¢ Change the battery provided with or identified for use with this product only in accordance with the instructions and limitations specified in this manual. â¢ Observe proper polarity orientation between the battery and battery charger.
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR ANY TYPE OF MOISTURE
Charging the Handset Battery Pack The batteries need charging when: â¢ The IN USE light on the base flashes. â¢ The handset beeps while you are on a call. Place the handset in the base so the CHARGING light goes on.The batteries will be fully charged in about 12 hours. You should charge the handset battery pack at least once every 90 days. Replacing the Handset Battery Pack 1. Remove the battery compartment cover on the handset by pressing on the indentation and sliding the cover downward. 2. Plug the battery pack cord into the handset, and tuck the cords in next to the battery. 3. Replace the cover by sliding it on its track.
Important Safety Instructions
THE LIGHTNING FLASH AND ARROW HEAD WITHIN THE TRIANGLE IS A WARNING SIGN ALERTING YOU OF âDANGEROUS VOLTAGEâ INSIDE THE PRODUCT. CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
1. Handset antenna 2. Earpiece 3. Talk button 4. Scan button 5. Recall button 6. Ringer on/off switch 7. Memory button 8. Redial button 9. Speed dial button 10. Pause button 11. Mute button 12. Volume button 13. Microphone 14. Handset charge contacts 15. Charge/In use indicator 16. Page button 17. Power line cord jack 18. TBR time switch 19. Telephone line cord jack
Making a Call 1. Press on the handset. 2. When you hear a dial tone, dial the number. Answering a Call If the handset is in the base, lift the handset. The IN USE light on the base goes on. If the handset is away from the base, press . The IN USE light on the base goes on. Ending a Call To end a call, place the handset in the base or press .
In Case of Difficulty
If the phone doesnât work at all, check these items first: â¢ Make sure the AC adapter is plugged in. â¢ Make sure the telephone line cord is plugged firmly into the base until and the telephone jack. â¢ Make sure the base antenna is fully upright. â¢ Make sure the battery pack is installed correctly. â¢ If you have rotary service on your phone line, make sure the dial mode switch is set to PULSE. â¢ You may be out of range when attempting to dial. Move closer to the base and try the call again. â¢ If the above suggestions donât solve the problem, the handset and base may not be communicating properly. Try the suggestions below to reset the security code. To reset the security code: â¢ Place the handset in the base, and check to make sure the CHARGING light is on. Wait 15 seconds, then . The phone should operate properly. If it doesnât, try the next step. pick up the handset and press â¢ Place the handset in the base, and check to make sure the CHARGING light is on. Unplug the AC adapter from the outlet, wait 15 seconds, then plug it in again.The CHARGING light should go on.Wait another 15 seconds, then pick up the handset and press . The phone should operate properly. if it doesnât try the next step. â¢ Pick up the handset, open the battery compartment, and unplug the battery pack. Wait 15 seconds, then reinstall the battery pack, close the battery compartment, place the handset in the base, and check to make sure the CHARGING light is on. Wait another 15 seconds, then pick up the handset and press . The phone should operate properly. If you have no dial tone: Check all the previous suggestions. If you still donât hear a dial tone, disconnect the phone and try another phone in the same jack. If there is no dial tone on that phone either, the problem is probably in your wiring or local service. Call your local telephone company. If you hear noise or interference when using the phone: â¢ Make sure the base antenna is fully upright. â¢ You may be out of range. Move closer to the base. â¢ Press and release to change to another of the multi channels available. If the noise is exceptionally loud, move closer to the base before changing channels. â¢ Household appliances plugged into the same circuit as the base can sometimes cause interference. Try moving the appliance or the base to another outlet. â¢ The layout of your home or office might the limiting the operating range. Try moving the base to another location, preferably on an upper floor. If the phone does not ring when you receive a call: â¢ Make sure the handset RINGER switch is set to ON. â¢ Make sure the telephone line cord is connected firmly to the base and the modular telephone pack. Make sure the AC adapter is plugged into an outlet not controlled by a wall switch. â¢ You might be too far from the base. Move closer to the base. â¢ You might have too many extension phones on your telephone line to allow all of them to ring. Try unplugging some of the other phones. â¢ Press to change to antoher channel. If you hear other calls while using your phone: â¢ Press to charge to another channel. â¢ Disconnect the base from the modular telephone jack and plug in a corded telephone. If you still hear other calls, the problem is probably in your wiring or local service. Call your local telephone service company. If you hear noise in the handset and the buttons donât work: You base unit and handset might not be set to the same security code. Place the handset in the base for at least 15 seconds to reset the security code.
RISK OF ELECTRIC SHOCK DO NOT OPEN
THE EXCLAMATION POINT WITHIN THE TRIANGLE IS WARNING SIGN ALERTING YOU OF IMPORTANT INSTRUCTIONS ACCOMPANYING THE PRODUCT.
SEE WARNING ON BOTTOM/BACK OF PRODUCT
Redial The last number dialed (up to 32 digits) on this phone is stored in redial memory until you dial another number. 1. Press . 2. When you hear a dial tone, press . Mute Mute allows you to hear you caller, but prevents the caller from hearing you. 1. Press while on a call. 2. To return to your conversation, press again. Handset Volume Control Each time you press the handset listening volume changes. Ringer On/Off - Battery Save Feature Set the handset RINGER switch to OFF to prevent the handset from ringing.You can still use the handset to make a call or to answer a call if you hear an extension phone ringing. When the handset RINGER switch is set to ON, the handset stays ready to use for up to 7 days.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE
When using the unit, basic safety precautions as below should always be followed to reduce the risk of fire, electric shock, or personal injury. 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on this unit. 3. Unplug this unit from wall outlets before cleaning. Do not use liquid or aerosol cleaners. Use of damp cloth for cleaning. 4. Do not use this unit near water, for example, near a bath tub, wash bowl, kitchen sink, or the like. 5. Install this unit securely on a stable surface. Serious damage may result if the unit falls. 6. Do not cover slots and openings of the unit, for they are provided for ventilation and protection against overheating. Never place the unit near radiators, in/or a place where proper ventilation is not provided. 7. Use only the power source as marked on unit. If you are not sure of the type of the power supply to your home, consult your dealer or local power company. 8. Do not place objects on the power cord. Install the unit where no one can step on the cord. 9. Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock. 10. Never push any objects into this unit through slots as they may result in risk of fire or electric shock. Never spill any liquid on the unit. 11. To reduce the risk of electric shock, do not disassemble this unit, but take it to a qualified serviceman when some service or repair work is required. Opening or removing covers may expose you to dangerous voltages or other risks. Incorrect reassembly can cause electric shock when the appliance is subsequently used. 12. Unplug this unit from the wall outlet and refer servicing to qualified service personnel under the following conditions: A. When the power supply cord or plug is damaged or frayed. B. If liquid has been spilled into the unit. C. If the unit has been exposed to rain or water. D. If the unit does not work normally by following the operating instructions. Adjust only controls covered by the operating instruction may require extensive work by a qualified technician. E. If the unit has been dropped or damaged. F. If the unit exhibits a distinct change in performance. 13. During thunderstorms, avoid using telephones except cordless types. There may be a remote risk of electric shock from lightning. 14. Do not use this unit to report a gas leak in the vicinity of it. 7 9 10 13 14 2
1 17 19 18
Page The page feature allows you to signal someone at the handset from the base.You can also use this feature to help you locate the handset. This feature is disabled when the handset RINGER switch is set to OFF. Press on the base. The handset signals for about 30 seconds, or until you turn it off by pressing on the base or on handset. Recall Press to activate custom-calling services such as Call Waiting or 3-Way Calling.You may have to press other buttons before or after as explained in custom-calling instructions provided by your local telephone company. Temporary Tone
NOTE: If you have touch tone service, you donât need to use the Temporary Tone feature. If you have dial pulse (rotary) service, this feature allows you to enter codes or tones needed to operate answering machines, or use electronic banking services, calling cards, and other special services. This feature will operate most special services; however, some services may actually require a touch tone line. To be sure, ask the company that provides the special service. 1. Dial the call, then press . Any buttons pressed after this send tone signals. 2. When you hang up to or press , the phone automatically returns to dial pulse (rotary) dialing.
16 6 8 12 11 15