|
|
|
Who's Online
There currently are 5775 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Copy of genuine owners/operators manual, very useful
;
The manual was a perfect match and was exactly what I was looking for. I'm very satisfied with my purchase.
;
Thank you for having the manual I needed for an older model Aiwa stero I had found on Ebay --- I wanted the Aiwa because I had tapes and cd's but I did not have a manual as to how to operate the system... I found what I needed and it has enabled me to set the system up for my enjoyment.
;
I wished detailed information of the JBL S310 and here I found it! Very happy with the service from this site!
;
The manual was very helpfull, it answerdes all my questions, and i was surprized to find the original manual on this site! Big thumbs uP:)
E9017FD_EN.qx3
03.8.6
10:13 AM
Page 13
VCR Manual Recording
Direct dubbing
Follow the steps below to copy a DVD or video disc to a videotape.This will be possible only if the DVD is not copy protected. Put a videotape in the cassette compartment. Make sure the tape�s record tab is intact and the tape is long enough to record the disc. Press VCR. Select the recording speed. Details are at �Selecting the recording speed (SP or LP)�. Put the DVD you want to copy in the disc tray. Press DVD. Press PLAY B.While disc is playing, press PAUSE k at the point you wish to start recording. Press DIRECT DUBBING to record. To pause the recording. Press PAUSE k. To resume recording. Press PAUSE k again. To stop the recording. Press STOP C.
Programming a Recording (TIMER)
Use a TIMER programming to automatically start and stop a recording at a later time or date.The System will switch to the right programme number and begin recording at the correct time.With this System, you can pre-programme up to eight recordings within a period of one year.To make a programmed recording, your System needs to know: * the date you want to make the recording * the programme number of the TV channel * the start and stop time of the recording * VPS or PDC on or off This information is saved in a TIMER block. What is 'VPS/PDC'? 'VPS' (Video Programming System)/ 'PDC' (Programme Delivery Control) are used to control the start and duration of TV channel recordings. If a TV programme starts earlier or ends later than scheduled, the System will turn on and off at the correct time. What do I need to know about 'VPS/PDC'? Usually the VPS or PDC time is the same as the start time. But if your TV guide shows a VPS or PDC time which is different from the programme�s scheduled start time, e.g. 20.10 (VPS/PDC 20.14), you must enter the VPS/PDC time exact to the minute. If you want a start time different from the VPS/PDC time, you must switch VPS/PDC off. English
General information
1 2 3 4 5 6 7
Recording(From DVD To VCR)
1 Insert a DVD without copyright protection in the tray. 2 Insert a video cassette tape with its erase prevention tab in place. 3 Select the recording speed. Details are at �Selecting the recording speed (SP or LP)�. 4 Enter �004� with numerical key pads to appear �DISC� on the TV screen. 5 Press REC I. 6 Change to DVD operation mode. 7 Press DVD, then PLAY B to begin the playback of a DVD. 8 Press VCR, then STOP C to stop recording.
Programming a recording (with the 'SHOWVIEW® system')
R
1 2
3 4
You no longer need to tediously enter the date, programme number, start and end time. All the information needed for programming is contained in the SHOWVIEW-programming number. You can find this SHOWVIEW number in most TV listing magazines written next to the concerned programme. Press SV/V+. ShowView system Enter the entire SHOWVIEW numShowView No. ber.This number is up to 9 digits long and can be found next to the 12345 � � � � start time of the TV programme in your TV listing magazine. [e.g: 1SET=SV/V+ 234-5 or 1 234 5] CORRECT=CLEAR END=EXIT If you make a mistake, you can clear your input with CLEAR. ShowView system Press SV/V+. � ONCE Select ONCE, DAILY or WEEKLY DAILY recording with K/L.Then press B. WEEKLY
SELECT K L CHOOSE B END=EXIT
Selecting once/daily/weekly recordings Using K/L, select from the following options: 'ONCE': Recording once 'DAILY': Repeated daily recordings (Monday to Friday) 'WEEKLY': Repeated weekly recordings (every week on the same day) '- -' appears at PROG. . * The programme number of the TV channel has not yet been assigned to the SHOWVIEW number. Using the numerical key pads, select the corresponding programme number (name) of the TV channel. The following message appears on the screen:'ERROR' * The entered SHOWVIEW number is incorrect. Correct your input or end with DISPLAY/STATUS/EXIT. * Check the time/date (see chapter 'Installing your video', section 'Setting the time and date'). * A daily recording was entered for the wrong day. Daily programming can only be used for recordings to be made from Monday to Friday. The following message appears on the screen:'TIMER NOT COMPLETED' * The channel is wrong.
13
|
|
|
> |
|
