There are currently no product reviews.
I did not have the manual for a Whirl Pool gas dryer, therefore I purchased it from Owner-manuals. This is exactly what I needed. Thank you for the service.
I was so pleased to get the owner`s manuel within one hour! Thanks again.
Finding the owners manual for my Pioneer CRWM62R is greatly appreciated. I had searched several other web sites with no success. Although my manual was not listed on your site for immediate download, I recevied an email within a few hours that my ower's manual was posted for me. I had no difficulty downloading the manual for my 20 year old multi-cassette player. Owner Manuals provides a service that is valuable, easy-to-use, accurate , efficient, and priced fairly. I thank you.
Excellent manual - just what I needed. Although currently available only in German, their are lots of pictures which makes it all very clear.
PHILIPS PE1642 Owner's Manual
you have complet fullfilled my expectance.
Price is OK.
6-32 x 5/8 Long Phillips Head Screws
Figure 4: Camera/Fixed Lens Mounting Position Zoom Lens Cameras: Use same procedure as fixed lens cameras. All hardware shown below must be used. See Figure 4a.
Figure 1: Remove Phillips Head Screws 2. Remove the end cap from the housing by pulling out the cradle assembly. See Figure 2.
Mounting Position For Cameras With TC9948 6X Zoom Lens. Use 1/4-20 x 1/2-Inch Screw Provided. Be Sure Plastic Washer Is In Place. Mounting Position For TC9948 6X Zoom Lens. Use 1/4-20 Screw Provided.
Figure 4a: Camera/Zoom Lens Mounting Positions LTC 9353/00 and LTC 9358/00 Only Note: Refer to section 5a for LTC 9352/01 model power wiring instructions. 5. When installing 120 or 220 volt cameras, the camera power cord must be cut leaving enough cable to strip and attach to the terminal block. Strip no less than 6 mm (1/4 in) and no more than 8 mm (5/16 in) of insulation away from the wires, making sure not to nick the wires. Attach the wires to the terminal block. See Figure 5 and Figure 6. Insert the loose end of the power supply cable or the remainder of the camera power cord through the lower right fitting. The fitting accepts cables with diameters from 1.8 mm (0.07 in) to 6.6 mm (0.26 in). Tie a figureeight knot in the wire to prevent strain on internal circuits. Repeat the same procedure for stripping the wires. Attach the wires to the opposite side of the terminal block. Crimp the ground wire to the ground lug located on the reverse side of the cradle. See Figure 5 and Figure 6.
CCD Camera Rear Cap
Figure 2: Remove Cradle Assembly 3. Place the camera/lens on the cradle assembly. Thewith a correct positioning for mounting either a camera fixed lens or a camera with a zoom lens is shown in Figure 3.
Figure 3: Camera/Lens Mounting Positions 4. Fixed Lens Cameras: Secure the camera/lens to the cradle with the 1/4-20 x 1/2-inch screw, nylon bushing, 5/16-inch flat washer, and 2.5 mm (0.100 inch) plastic washer. Make sure the thermoplastic shield is under the camera in the correct position. Be sure that the nylon bushing is in place. All hardware shown below must be used. For LTC 0240 Series cameras, use 1/4-20 x 7/8 inch BHCS, nylon bushing, 5/16-inch flat washer, and 9.8 mm (0.385 inch) plastic spacer. See Figure 4.
2000 Max. 250 Min.
Figure 5: Cut Camera Power Cord Note: If power is supplied from a pan/tilt feed thru, follow the same instructions as above for wiring procedures. Figure 6 shows the relationship with color codes. Hint: For ease of wiring, remove the terminal block from its mounted position. Wire accordingly and remember to maintain polarity. Remount the terminal block with the wires in place. See Figure 6.
5/16 Inch Flat Washer Nylon Bushing 1/4-20 x 1/2 Screw
Mounting Position For Camera With Fixed Lens. Use 1/4-20 x 1/2 Screw