|
Who's Online
There currently are 310 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
 |
|
There are currently no product reviews.
 ;
I was very glad recieving the service manal from You. Additionaly very fast. Extremaly nice servicing. Thanks very mach! Now my GX-220 working better, than it was made. Alexander from Moscow, Russia/
 ;
Sweet! I won the item on eBay and couldn't adjust the geometry or even keep a steady picure. This guide has the full schematics (not available anywhere else as far as I could tell), and was a bargain for the wealth of knowledge it contains. I hooked it up to my testing equipment, tweaked a few potentiometers and got it playing videogames in no time. Thanks!
 ;
It was just what I need to fix my old BMW's CD player. Very convenient also. Thank you.
 ;
Great Manual! It contains all the wiring schematics and mechanical exploded views that are essential for service and repair. I was surprised I even found this for such an old machine. Only wish I knew of this site many years ago.
 ;
Great manual very clear copied. You are making an incredible job. I appreciate a lot the rapidity and your efficiency. Thanks a lot
Alignments
L04E AB
8.
EN 71
8. Alignments
Index of this chapter: 1. General Alignment Conditions 2. Hardware Alignments 3. Software Alignments and Settings Note: ⢠The Service Default Mode (SDM) and Service Alignment Mode (SAM) are described in chapter 5 âService Modes, ...â. ⢠Menu navigation is done with the CURSOR UP, DOWN, LEFT, or RIGHT keys of the remote control transmitter. SATURATION/COLOR to â0â. CONTRAST to â0â. BRIGHTNESS to minimum (OSD just visible). Return to the SAM via the MENU key. Connect the RF output of a pattern generator to the antenna input. Test pattern is a 'black' picture (blank screen on CRT without any OSD info) with a signal strength of 1 V_pp. 10. Set the channel of the oscilloscope to 50 V/div and the time base to 0.2 ms (external triggering on the vertical pulse). Ground the scope at the CRT panel and connect a 10:1 probe to one of the cathodes of the picture tube socket (see diagram B). 11. Measure the cut off pulse during first full line after the frame blanking (see figure âV_cutoff waveformâ). You will see two pulses, one being the âcut offâ pulse and the other being the âwhite driveâ pulse. Choose the one with the lowest value; this is the âcut offâ pulse. 12. Select the cathode with the highest V_dc value for the alignment. Adjust the V_cutoff of this gun with the SCREEN potentiometer (see figure âTop view family boardâ) on the LOT to 160 V_dc, except for the 25/28BLD picture tube (Black Line Display, for EU only); this tube must be aligned to 140 V_dc. 13. Restore BRIGHTNESS and CONTRAST to normal (= 31). 5. 6. 7. 8. 9.
8.1
General Alignment Conditions
Perform all electrical adjustments under the following conditions: ⢠AC voltage and frequency: 120 V_ac / 60 Hz or 240 V_ac / 50 Hz (region dependent). ⢠Connect the set to the Mains voltage via an isolation transformer with a low internal resistance. ⢠Allow the set to warm up for approximately 20 minutes. ⢠Measure the voltages and waveforms in relation to chassis ground (with the exception of the voltages on the primary side of the power supply). Never use the cooling fins / plates as ground. ⢠Test probe: Ri > 10 Mohm; Ci < 2.5 pF. ⢠Use an isolated trimmer / screwdriver to perform the alignments.
max.
8.2
Hardware Alignments
0V Ref.
VCUTOFF [VDC]
E_06532_011.eps 110204
Figure 8-2 V_cutoff waveform
C 1504 1506
8.2.2
Focusing 1. Tune the set to a circle or crosshatch test pattern (use an external video pattern generator). 2. Choose picture mode NATURAL (or MOVIES) with the SMART PICTURE button on the remote control transmitter. 3. Adjust the FOCUS potentiometer (see figure âTop view family boardâ) until the vertical lines at 2/3 from east and west, at the height of the centreline, are of minimum width without visible haze.
7990
7601 9275 SDM 9252 1221 A 5512 B Focus Screen VG2 LOT
1204
1000 (TUNER)
D 1005 ComPair E_14480_030.eps 130204
Figure 8-1 Top view family board 8.2.1 Vg2 Adjustment 1. Activate the SAM. 2. Go to the WHITE TONE sub menu. 3. Set the values of NORMAL RED, GREEN and BLUE to â32â. 4. Go, via the MENU key, to the normal user menu and set
|
|
 |
> |
|