There are currently no product reviews.
Hello from Germany - thank you very much for the manual for my Sharp "Searcher" - the handling of your internet area is outstanding..Mike
I am very happy with the owner's manual. I bought a used Casio and was so relieved that I was able to get a hold of a owner's manual. It was very easy to download the manual and I had no problems with printing it. Thank you! Nancy Whalen
The purchased manual is an high-quality scan of the original JVC paper-based OwnerΒ΄s Manual. I am very satisfied!
Very satisfied with received document, all is right, Thank You very much, it was a Pleasure to work with You.
great site, the most easy and fastest way to find the manual you need, no 5 star because the manual was only available in german, but I speak german as well so no problem for me.
MINI HIFI SYSTEM
STANDBY ON NEWS/TA
5 Press CLOCK/TIMER again to store the setting. â¢ The clock starts. â¢ To exit without storing the setting, press Ã on the system.
â¢ The system can switch on to CD, TUNER, or TAPE 2 mode automatically at a preset time. It can serve as an alarm to wake you up. â¢ Before setting the timer, make sure the clock is set correctly. â¢ The timer will always be switched on once it is set. â¢ The volume of the timer will increase from the minimum level until the volume level before the set is switched to standby mode. 1 Press and hold CLOCK/TIMER for more than 2 seconds to select timer mode. â¢ âAM 12:00â or â00:00" or the last timer setting starts flashing depending on whether you have selected 12- or 24-hour mode. â¢ The TIMER starts flashing. â¢ The selected source is lit while other available sources are flashing. 2 Press CD, TUNER or TAPE to select the desired source. â¢ Before selecting CD or TAPE, make sure a CD or tape is loaded in the CD tray or tape deck 2. 3 Press Ã or Ã¡ on the system to set the hour for the timer to start. 4 Press Ã or Ã« on the system to set the minute for the timer to start.
C O N T
C1 â¢ 2 â¢ 3 CD
You can view the clock (if it is set) if the system is in Standby mode or when any sound source is selected (CD, TUNER, etc.). The clock will be displayed for about 7 seconds. â¢ Press CLOCK/TIMER briefly (or CLOCK on the remote control). â¢ "PM 10:38 or 22:38" (the current time) will be displayed depending on whether you have selected 12- or 24-hour mode. â¢ "--:--" will be displayed if the : clock is not set.
The clock can be set in either 12- or 24hour mode, e.g. "AM 12:00" or "00:00". Before setting the clock, you must be in the View Clock mode. 1 Press CLOCK/TIMER to select clock mode. 2 Press PROG (on the system only) to select 12- and 24- hour mode. â¢ If 12-hour mode is selected, "AM 12:00" starts flashing. â¢ If 24-hour mode is selected, "00:00" starts flashing. 3 Set the hour with Ã or Ã¡ on the system. 4 Set the minute with Ã or Ã« on the system.
Note: â When the system goes into low power standby mode, the clock setting will not be displayed.
CDR/DVD AUX CDR
PRESET v SIDE NEXT
Notes: â During clock setting, if no button is pressed within 90 seconds, the system will exit clock setting mode automatically. â When a power interruption occurs, the clock setting is erased. â To set the time with RDS clock, see "Receiving RDS Radio Station" under TUNER section.
3/6/00, 2:24 PM
3139 116 19681