There are currently no product reviews.
Ottimo manuale, grafica ferfetta invio rapidissimo. Altissimo livello!!!!!
Great PDF easy to read good info needed for replacment of belts and assembly and specs.
complete and unabridged very good quality
easy to download.
recieved in two days.
Awesome manual. Complete diagrams of all board assemblies as well as how to get to each part of the t.v. down to the individual screws and their locations. Get it.
perfect copy, im very satisfied, i was need the diagram over the powersupply and
the copy was very sharp
Demonstration Switching the system to Standby Sound Navigation Display mode mode The system has a demonstration mode that There are four different display modes for
For optimal sound listening, select only one
shows various features offered by the system. selection. In Demonstration mode
of the following navigation sound controls
To activate demonstration and hold DEMO STOP Ã on the q Press DISPLAY repeatedly to select NORMAL, at a time : wOOx, DSC or VAC.
q In Standby mode, press and hold DEMO system. 1, 2, or MODE 3.
STOPÃon the system until "DEMO ON" is NORMAL ........ All available LEDs will light up wOOx displayed. In any other source mode (except Eco and display screen will have There are three wOOx settings to enhance the Â§ The demonstration will begin. Power Standby mode) full brightness. The VU meter will bass response.
q Press STANDBY ON (or B on the remote be in music mode.
MODE 1 .......... All available LEDs will light up switch ON (enhanced) or OFF effect. q When wOOx is switched on;
1 Press wOOx ONâ¢OFF to
To deactivate the demonstration control).
and the display screen will have
full brightness. The VU meter will
be in volume mode.
q Press and hold DEMO STOP Ãon system Â§ The clock will appear on display when the (normal) the wOOx sound until "DEMO OFF" displayed. system is in Standby mode. Â§ The system will switch to Standby mode.
Note: Switching the system to Eco MODE 2 .......... All available LEDs will light up Â§ and the last selected wOOx level will â Even if you remove AC power cord and the display screen will be at appear on the display. Power Standby mode (< 1 Watt) reconnect it to wall socket, the demonstration half brightness. The VU meter q When wOOx is switched off; will remain off until you activate it again. Â§ The display will show "WOOX NORM" and the remote control). MODE 3 .......... The display screen will be at half Â§ "ECO POWER" will be displayed, then the WOOX brightness. The VU meter and all
will disappear from the display. LEDs will be off. Â§ The low power ECO POWER LED will be (or press wOOx LEVEL on the In Standby/Demonstration mode lighted. remote conrol) to select the desired wOOx q Press STANDBY ON.
q Press ECO POWER (or press and hold B on will be in music mode.
display screen will go blank.
Switching the system on 2 When is switched on, adjust wOOx
Volume Control level: 1, 2 or WOOX 3.
Â§ The system will switch to the last selected Note: â If you have not deactivated the demonstration, it
Adjust VOLUME to increase (turn knob source. Note: clockwise press VOLUME +) or decrease q Press CD, TUNER, TAPE, AUX (or CD 123, â Some discs or tapes might be recorded in high (turn knob anti-clockwise or press VOLUME -) TUNER, TAPE 1/2 or AUX/CDR on the modulation, which causes a distortion at high the sound level. remote control). volume. If this occurs, deactivate wOOx or reduce To listen through the headphones Power Saving Automatic Standby As a power-saving feature, system will q Connect headphones plug to the n socket buttons or OPENâ¢CLOSE.
will resume five seconds after the system switches
to Eco Power or Standby mode. q Press any one of the DISC DIRECT PLAY
Â§ The system will switch to selected source. the volume.
Automatic DSC-wOOx / VAC-wOOx
Â§ The system will switch to CD mode. In Eco Power Standby mode not press any buttons within 30 minutes after a Â§ The speakers will be muted. The best wOOx setting is generated
automatically switch to Standby mode if you do at front of the system. disc or tape has stopped playing. q Press ECO POWER. Â§ The system will switch to last selected source.
q To restore the volume, press MUTE again or To switch off the volume temporarily q Press MUTE on the remote control.
automatically for each DSC or VAC selection.
You can manually select the wOOx setting that
best suits your listening environment.
q Press CD 123, TUNER, TAPE 1/2 or AUX/ "MUTE" will be displayed. CDR on the remote control. Â§ The system will switch to the selected source.
increase the VOLUME level.
Â§ Playback will continue without sound and