There are currently no product reviews.
perfect! you just sent to me the copy in Italian witout even my specification!!!! so you are really smart cooperative and efficient. To my opinion the best place all over to get a manual of electronics!!!!
Well Well Well!!!! Good manual perfect for my hobby!!! As Before you have done a very well done work!!!! Thank you
Super nice! Good to have a manual in digital format.
Great job supplying the manual.
Many of these products weerepretty obscure, so it was great that you had
the manual for it!
Great manual, would not have been able to operate my machine without it!!
James Dawson August 18, 2012
Playing a Disc
Press PLAYÃ to start playback. Ã
â The disc tray, track number and elapsed playing time of the current track appear on the display. Â¶ To interrupt playback, press PAUSEÃ . Ã
â The playing time flashes. Â¶ To resume playback, press PLAYÃ again. Ã
2 To stop playback, press Ã. Note: â All the available discs will play once, then stop.
Searching for a particular passage during playback
Â¶ Press and hold Ã or Ã¡ until the desired passage is located. â The volume will be reduced. Â¶ Play returns to normal when Ã or Ã¡ is released.
Programming tracks of a loaded disc is possible when playback is stopped. The display will indicate the total tracks stored in the programme. Up to 40 tracks can be stored in the memory in any order. When 40 tracks are stored and you attempt to store another track, the display will show âFULLâ.
You can change the outer two discs while the third inner disc is stopped or is playing. Press DISC CHANGE. â The CD changer tray slides out. 2 Replace the discs in the left and right disc trays. Â¶ If you wish to change the inner disc during playback, press DISC CHANGE again. â "DISC CHANGE" will be displayed. â The disc will stop playing. â The CD changer tray will close to retrieve the inner disc and then open again with the inner disc accessible. 3 Press OPENâ¢CLOSE to close the CD changer tray.
1 2 3 4 5
Load the desired discs in the disc trays. Press PROGRAM to start programming. â The PROG flag starts flashing. Press the CD (CD 1â¢2â¢3) or DISC 1/2/3
button to select the disc. PressÃ or Ã« to select the desired track. Press PROGRAM to store the track. Â¶ Repeat steps 3 to 5 to store other discs and tracks. 6 Press Ã once to end programming. â The total number of tracks programmed and total playing time appear on the display.
Selecting a desired track when playback is stopped Press Ã or Ã« until the desired track appears on the display. Press PLAYÃ to start playback. Ã
â The selected track number and elapsed playing time appear on the display.
or if one of the programmed tracks has a number greater than 30, then â--:--â appears on the display instead of the total playing time. â If the system is reading the discs, programming is not possible, âREADINGâ will be displayed and followed by "DISC X". "X" is the current read disc number. â During programming, if no button is pressed within 20 seconds, the system will exit programme mode automatically. â âSELECT A DISCâ will be displayed when programming an empty disc slot.
Selecting a desired track during playback Â¶ Press Ã or Ã« until the desired track appears on the display. â The selected track number and elapsed playing time appear on the display. Â¶ If you press Ã once it will skip to the beginning of the current track and play the track again. Note: â PressingÃ during shuffling can only skip to the beginning of the current track.
pg 01-30/C380/22-Eng 17 12/7/00, 3:43 PM
3139 115 20641
Selecting a desired track
Notes: â If the total playing time is more than â99:59â