PHILIPS AZ2045/14
Owner's Manual

DIGITAL TUNER
3 Press and hold � or § until the frequency in the display starts running. � The radio automatically tunes to a station of sufficient reception. Display shows during automatic tuning. � If a FM station is received in stereo, is shown. 4 Repeat steps 2-3 if necessary until you find the desired station. � To tune to a weak station, press � or § briefly and repeatedly until you have found optimal reception. To improve radio reception: � For FM, extend, incline and turn the telescopic aerial. Reduce its length if the signal is too strong. � For MW (LW), the set uses a built-in aerial. Direct this aerial by turning the whole set. Programming radio stations You can store up to a total of 30 radio stations in the memory, manually or automatically (Autostore). Manual programming 1 Tune to your desired station (see Tuning to radio stations). 2 Press PROG to activate programming. 3 Press PRESET DOWN/ UP once or more to select a preset number. 4 Press PROG to confirm. 5 Repeat steps 1-4 to store other stations. Note: You can erase a preset station by storing another frequency in its place.

CD
After all stations are stored, the first autostore preset station will then automatically play. To listen to a preset or autostore station Press the PRESET (up or down) buttons once or more until the desired preset station is displayed. Changing tuning grid (some versions only) In North and South America the frequency step between adjacent channels in the MW (LW) and FM band are 10 KHz and 100 KHz respectively. In the rest of the world this step is 9 KHz and 50 KHz. Usually the frequency step has been preset in the factory for your area. 1 Check that the set is completely switched off. 2 To select 9KHz: Simultaneously, press MODE and PRESET DOWN on the set. 3 Switch the set on to TUNER and then release the controls. � To select 10KHz: Repeat steps 1-3 but in step 2, simultaneously, press MODE and PRESET UP on the set. � When you tune to radio stations, the display shows tuning in either steps of 9 kHz or 10 kHz. � All preset and autostore stations will be affected and you may need to reprogramme stations. CD PLAYER Playing a CD This CD player plays Audio Discs including CD-Recordables and CD-Rewritables.

CD
3 Press 2; to start playback. � if your CD contains non-audio files 4 To pause playback press 2;. Press 2; again to resume play. 5 To stop CD playback, press 9. Note: CD play will also stop when: � the CD door is opened � the CD has reached the end � you select tape or tuner source. Selecting a different track � Press � or § on the set, once or repeatedly to select. � In the pause/stop position, press 2; to start playback.

CASSETTE RECORDER
Programming track numbers In the stop position, select and store your CD tracks in the desired sequence. Up to 20 tracks can be stored in the memory. 1 Press � or § on the set to select your desired track number. 2 Press PROG. � If you attempt to programme without first selecting a track number, is shown. 3 Repeat steps 1-2 to select and store all desired tracks. � Display: if you try to programme more than 20 tracks. Reviewing the programme In the stop position, press and hold PROG until the display shows all your stored track numbers in sequence.

1 Press y to on, then SOURCE to select CD. Autostore � if no CD is inserted. Autostore automatically starts programming radio 2 Insert a CD with the printed side facing up and stations from preset 1. Available stations are close the CD door. programmed in order of waveband reception strength: � Display: total number of tracks and playing time. FM, followed by MW (LW). Any previous presets e.g. � is shown if you have inserted a manually programmed will be erased. non-finalized CD-R(W). � Press PROG for 4 seconds or more to activate autostore programming. � The display shows AUTO, program blinks, followed by the radio station details when stored. (See 5)

Finding a passage within a track 1 Press and hold � or §. � The CD is played at high speed and low volume. 2 When you recognize the passage you want, release Erasing a programme � or § to resume normal playback. You can erase the programme by: � pressing 9 twice Note: During a CD program or if shuffle/ repeat � is displayed briefly and active, searching is only possible within a track. disappears. � selecting TAPE or TUNER source. Different play modes: SHUFFLE and REPEAT You can select and change the various play modes CASSETTE RECORDER before or during playback, and combine the modes Cassette playback with PROGRAM. 1 Press y to on, then SOURCE to select TAPE. shuffle � tracks of the entire CD/ program are � Display: shows throughout tape played in random order operation. shuffle and repeat all � to repeat the entire CD/ 2 Insert a cassette and close the door. programme continuously in random order 3 Press PLAY 2 to start playback. repeat all � repeats the entire CD/ program 4 To pause, press PAUSE ;. Press again to resume. repeat (and shuffle repeat) � plays the current 5 Press SEARCH 5 or 6 to fast wind the tape. (random) track continuously 6 To stop the tape, press STOP 9. � The keys are automatically released at the end of a 1 To select play mode, press MODE once or more. tape, except if PAUSE ; has been activated. 2 Press 2; to start playback if in the stop position. 3 To select normal playback, press MODE repeatedly until the various modes are no longer displayed. � You can also press 9 to cancel your play mode.