PHILIPS AZ1330D/79
Owner's Manual

Docking Entertainment System

AZ1330D

Hearing Safety
� Listen at a moderate volume. Using headphones at a high volume can impair your hearing. This product can produce sounds in decibel ranges that may cause hearing loss for a normal person, even for exposure less than a minute. The higher decibel ranges are offered for those that may have already experienced some hearing loss. Sound can be deceiving. Over time your hearing "comfort level" adapts to higher volumes of sound. So after prolonged listening, what sounds "normal" can actually be loud and harmful to your hearing. To guard against this, set your volume to a safe level before your hearing adapts and leave it there. To establish a safe volume level: � � � � � � � � � Set your volume control at a low setting. Slowly increase the sound until you can hear it comfortably and clearly, without distortion. Listen for reasonable periods of time: Prolonged exposure to sound, even at normally "safe" levels, can also cause hearing loss. Be sure to use your equipment reasonably and take appropriate breaks. Be sure to observe the following guidelines when using your headphones. Listen at reasonable volumes for reasonable periods of time. Be careful not to adjust the volume as your hearing adapts. Do not turn up the volume so high that you can't hear what's around you. You should use caution or temporarily discontinue use in potentially hazardous situations. Do not use headphones while operating a motorized vehicle, cycling, skateboarding, etc.; it may create a traffic hazard and is illegal in many areas.

1
1

English
Supplied accessories
# @ ! 0 9 8
6 x R20 � UM-1 � D-CELLS
AUX

Controls / Power Supply
For Tuner: � tunes to a radio station 9 � stops disc playback; � erases a program DBB � turns on/off bass enhancement @ p � 3.5 mm stereo headphone socket Helpful hints: The speakers will be muted when headphones are connected to the set. # AUX jack � connects an external source (3.5 mm socket) $ Battery door � opens to insert 6 x 1.5V R-20/ -UM1/ D-cells % Disc tray � load a disc ^ iR � infrared sensor for remote control

DOCK

2 3
VOLUME

User manual

�

DOCKING ENTERTAINMEN T S YSTE M A Z1330 D

DOCK FOR

for

� AC power cord � Remote control � Docking kit � 1 x Apple iPod dock (pre-installed with the main set) � dock adaptors (8 adaptors for different iPod types) � 1 dust cover (keep the dock connector from covering dust and dirt) � Line-in cable

DBB

ALBUM/PRESET SO URCE

4 5 6 7

ALBUM/PRESET +

PROG

DE

POWER

Top and front panels (See 1)
1 Telescopic antenna � improves FM

$

reception 2 DOCK � selects dock source 3 Dock connector � connects iPod player 4 VOLUME/VOL +/- � adjusts volume level & * ( ) ¡

Remote control (See 1)
CD � selects disc mode TUNER � selects tuner mode DOCK � selects dock (iPod) source AUX� selects AUX mode 9 � stops disc playback; � erases a program � REPEAT � repeats a track/disc/all programmed tracks £ SHUFFLE � turns on/off the random play mode � DBB � turns on/off bass enhancement � MUTE �mutes or restores the volume

% ^

MP3 -WMA PLAYBACK

5 MODE � selects different play modes: e.g. REPEAT or SHUFFLE (random order) 6 PROGRAM For disc � programs tracks and reviews the program For Tuner � auto searches and stores radio stations
*

iR

&

(

7 ALBUM/PRESET +/- ( 3, 4 ) For MP3-CD/ WMA play: � select albums For Tuner � selects a preset radio station 8 / � opens/closes the disc tray

Power Supply
Whenever convenient, use the power supply cord if you want to conserve battery life. Make sure you remove the plug from the set and wall outlet before inserting batteries. Batteries Main set (See 1) Insert 6 batteries, type R-20, UM1 or Dcells (not included, preferably alkaline) with the correct polarity.

@ ¡ 8 6 £ 4 �

) � 7 �

9 SOURCE: � selects CD/MP3-CD, DOCK mode,Tuner or AUX 0 POWER � powers on/off the system ! 2; � starts or pauses disc/DOCK playback �§ For disc/ DOCK play: � skips to the beginning of a current/ previous/ later track � fast searches backwards and forwards within a track �

NOTES
Meet Philips at the Internet http://www.philips.com
English

2

8

Power Supply
Remote control Important! � Before using the remote control, remove the insulation plastic tab as shown in figure 9. � If the remote control does not function correctly or the operating range is reduced, replace the battery with a new (CR2025) type battery. 1 2
X

�

Disconnect the power cord from the wall socket to protect your set during heavy thunderstorms. Children could seriously injure themselves as the free end of the cable may still be live if only the connector is removed from the MAINS socket at the back of the unit. The type plate is located on the bottom of the set.

3

Pull the battery tray out as shown in figure 9. Replace a new battery according to polarity indication, and fully insert the battery tray back to the original position. Incorrect use of batteries can cause electrolyte leakage and will corrode the compartment or cause the batteries to burst: Do not mix battery types: e.g. alkaline with carbon zinc. Only use batteries of the same type for the set. When inserting new batteries, do not try to mix old batteries with the new ones. Remove the batteries if the set is not to be used for a long time. Batteries contain chemical substances, so they should be disposed of properly. �

Auto power saving In CD and DOCK mode, if AZ1330D is in the PAUSE position for 5 minutes, it will auto switch to the stop position.

4

�

�

In CD and DOCK mode, if AZ1330D is in the STOP position for 15 minutes, it will auto switch to standby to save power. Helpful hints: To avoid unnecessary energy consumption, always press POWER on the set to power off the set after using the set.

W
5
CLASS 1 LASER PRODUCT

�

�

� �

CAUTION
- Visible and invisible laser radiation. If the cover is open, do not look at the beam. - High voltage! Do not open.You run the risk of getting an electric shock.The machine does not contain any user-serviceable parts. - Modification of the product could result in hazardous radiation of EMC or other unsafe operation.

Using AC power

6

9

1

AZ1330D

2
M O

Check if the power/mains voltage, as shown on the type plate located on the bottom of the set, corresponds to your local power supply. If it does not, consult your dealer or service center. Connect the power cord to the AC~ MAINS inlet and the wall socket.The set is now ready for use. To switch the set off completely, withdraw the power cord from the wall socket. Install the unit near the AC outlet and where the AC power plug can be easily reached.

7

3

3 1 Printed in China PDCC-JH-0721

2
4