|
|
|
Who's Online
There currently are 5628 guests and
3 members online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Purchased the manual that I was looking for at a great price and could download it easily.. Great service experience and for future purchases I plan to use the site.
Thank you very much
;
Exactly what was needed to assess the product - excellent value and great service
;
A site where discontinualed schematic diagrams and back dated information can be found on discontinued radios tv's and any electronic equipment can be found. Newer manuals either Service and operating manuals. Radio amateurs should find this site a great source for ham radio equipment manuals. I will return to this site should I need information on any electrical equipment. priced easy to download in a PDF format and print pages need to undertake the repair.
;
Quality scan of the original. All the detail necessary to troubleshoot, repair and adjust the unit. I'm sure I will be downloading more manuals in the future as the need arises.
;
Exactly as described, a Service Manual complete with the schematics and PCB layout delivered in a timely manner. Many thanks for the great service.
English
2 Insert a CD and, if desired, program the track numbers. Under no circumstance should you try to If you are unable to solve a problem by
O P N E
PA USE
ST OP�R ECOR
repair the set yourself as this will following these hints, consult your dealer or
AR CH
PLA YRECORD
service center.
SE
3 Press STOP·OPEN 9 / to open theinvalidate cassettethe compartment.guarantee.
D
4 Insert a blank, unprotected, and close the cassette
INSTRUCTION FOR USE
compartment.
Problem Possible cause Solution
No sound, VOLUME is not adjusted. Adjust volume. 5 Press RECORD 0 to start recording. no power Headphones are connected. Disconnect headphones.
� Playing of the CD or program starts automatically.
Mains is not securely connected. Connect mains cable properly.
6 For brief interruptions press ;. Press the PAUSE ; key Batteries are flat. Insert fresh batteries.
Trying change over to Remove mains plug from the battery supply without removing the plug. unit�s AC MAINS socket. 7 To stop recording, press STOP·OPEN 9 /. No reaction to Electrostatic discharge. Disconnect the set from power supply, operation of any keys reconnect after a few seconds. Note: the recording can be started from different positions: Poor reception Weak radio signal. Direct the antenna for optimum � if the CD player is in pause mode, recording will start
again to resume recording. Batteries are inserted incorrectly. Insert batteries correctly.
reception. from this very position (use � or §); like TVs, computers, engines, etc. equipment. beginning of the CD or program. No CD is inserted. Insert a CD. The laser is steamed up. Wait until the lens has cleared. 1 Tune to the desired radio station (see �RADIO�).
2-7
� if the CD player is in stop mode, recording will start from Interference caused by equipment Keep the radio away from electrical
no E indication The CD is badly scratched dirty. Replace or clean the CD.
Recording from the radio The is inserted upside down. Insert CD with label facing up.
skips tracks The CD is damaged dirty. Replace or clean the CD. Poor cassette Dust dirt on the capstans or Clean heads, capstans, and pressure sound quality pressure rollers. 3 Insert a blank, unprotected, and close the cassette (METAL or CHROME) for recording. Recording does Cassette tab(s) may be snapped off. Apply a piece of adhesive tape over 4 Press RECORD 0 to start recording. not work the opening.
2 Press STOP·OPEN 9 / to open the cassette compartment. PROGRAM is active. Switch off SHUFFLE or PROGRAM.
compartment. Use of unsuitable cassette types Only use NORMAL type cassettes for
5 For brief interruptions PAUSE ;. To resume recording press
the PAUSE ; key again.
6 To stop recording, press STOP·OPEN 9 /.
11 13
English
CS 49 108
CASSETTE RECORDER TROUBLESHOOTING
Recording from the player � CD synchro start
ST AR T RECO RD IN G
below before taking the set for repair.
CD SY N CH RO
1 Set the POWER slider to CD. WARNING
If a fault occurs, first check the points listed
|
|
|
> |
|
